Latest Products https://www.advancetechinstruments.co.in Latest Products Fri, 03 Jul 2020 06:51:23 +0530 en-us https://www.advancetechinstruments.co.in Digital Bursting Strength Tester https://www.advancetechinstruments.co.in/digital-bursting-strength-tester.htm https://www.advancetechinstruments.co.in/digital-bursting-strength-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 A test piece, placed over a circular elastic diaphragm, is rigidly clamped at the periphery but free to bulge with the diaphragm. Hydraulic fluid is pumped at a constant rate, bulging the diaphragm until the test piece ruptures. The bursting strength of the test piece is the maximum value of the applied hydraulic pressure.The pneumatic clamping in such a way the clamping pressure against the specimen can be corrected by the adjustment of air pressure regulator. It is important that the specimen is clamped so hard so that it does not slip during testing. The standard clamping pressure is 3.0 kg/cm2. A bursting strength tester of the hydraulic type consisting of :Two clamping plates upper and lower clamping and parallel surfaces having a a central circular opening. The lower edge of the opening, Which makes contact with the test piece is slightly rounded, but not so much as to effect the area of the aperture. The pressure is generated by a motor driven piston which forces a liquid contain no air. The motor direction reverses automatically after the sample burst.for instance, pure air free glycerol (96%) or ethylene glycol into a pressure chamber beneath the diaphragm at a rate of 2.9ml/s ± 0.1 ml/s. The hydraulic system designs in such and Note : Glycerol is preferred to ethylene glycol as the hydraulic fluid because its higher viscosity.Electronic Bursting Strength Tester meets the requirements laid down in the testing standards as per  TAPPI standards. Vertical Tensile Tester https://www.advancetechinstruments.co.in/vertical-tensile-tester.htm https://www.advancetechinstruments.co.in/vertical-tensile-tester.htm Thu, 12 Sep 2019 00:00:00 +0530  Tensile Strength, the maximum force developed a test specimen before rupture on the tensile test carried to rupture under prescribed conditions. Tensile Strength (as used here) is the force per unit width of test specimen. Stretch, the maximum tensile strain developed in the test specimen before ruptrure in a tensile test carried to rupture under prescribed conditions. The stretch (or percentage elongation) is expressed in a percentage i.e. one hundred times the ratio of the increase in length of the test specimen to the original test span.Details : Tensile energy absorption (TEA), the work done when the specimen is stressed to rupture in tension under prescribed conditions as measured by the integral of the tensile strength over the range of tensile strain from zero to maximum strain. The TEA is expressed as energy per unit area (test sapn X width) of test specimen. Breaking Length, the calculating limiting length of strip of uniform width, beyond which, if sucha strip were suspended by one end, it would break of its own weight. Tensile Index, the tensile strength in N/m divided by grammage. Digital GSM Tester https://www.advancetechinstruments.co.in/digital-gsm-tester-supplier.htm https://www.advancetechinstruments.co.in/digital-gsm-tester-supplier.htm Thu, 12 Sep 2019 00:00:00 +0530 In this model the GSM Tester directly gives GSM (grams per sq. meter) weight of the sample. Condition the specimen as per SCAN P-2, The conditioning atmosphere in testing paper and board are Temp.23 +1 C relative humidity 50% +2% A Stainless steel rectangular template size 20x25 cm OR 10X10 cm to cut the paper sample. Place the sample in sample basket on the scale. Read the basis is weight/substance on scale.Specification : Mode A Weight up to 300gm Mode B Scale 10 x 10 Mode C Scale 20 x 25 Mode D Scale 25 x 40 Digital Ring Crush Tester https://www.advancetechinstruments.co.in/digital-ring-crush-tester.htm https://www.advancetechinstruments.co.in/digital-ring-crush-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The ring crush resistance of paper and paperboard is the maximum compressive force that a test piece will sustain without being crushed, the test piece being in the form of a cylinder, standing on one end, and the force being applied to the other end under specified conditions. This method applies to papers and paperboards with a thickness of not less than 0.15 mm and not more than 0.49 mm.   Details : It is primarily intended for corrugated media, liner and other papers and boards for use in the manufacture of packaging cases and boxes. The test piece is placed in a holder containing as annular groove so that it forms a cylinder with a horizontal base. It is then subjected to a uniformly increasing force in a testing machine until crushing occurs. Photo Brightness Tester https://www.advancetechinstruments.co.in/photo-brightness-tester.htm https://www.advancetechinstruments.co.in/photo-brightness-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The model is having three search unit (sensor unit) determines the reflectance of the surface of the objects, as well as the colour, by measuring the light reflected from their surface and then comparing to standards. The instrument consists of a Sensor Unit and a Photometer. The Sensor Unit provides the light source and the measurement transducers (Photocells). The outputs of the Sensor Unit are fed to photometer where they are processed and converted into a digital reading, which is displayed on the front panel.Applications : A useful comprehensive list of application is given in other literature along with appropriate S.U., filters, and applicable standard methods. Below, some of these applications are put into prospective, with only the most widespread and important ones mentioned. Paper Industry - Our instrument is widely used to measure the “paper brightness” using S.U. “W”, which has a blue filter built in. gloss measurement using S.U. “P” and opacity measurement using S.U. “Y” with green tristimulus filter are also possible. For opacity the instrument is first set to read 100, with the sample placed on white plaque. Then a reading is taken with the sample on black surface this reading is % opacity. Folding Endurance Tester https://www.advancetechinstruments.co.in/folding-endurance-tester.htm https://www.advancetechinstruments.co.in/folding-endurance-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Two horizontally opposed and movable clamping jaws, which hold a specimen 100 mm (4 in.) long under variable tension during the folding cycle, while a slotted folding blade, sliding back and forth between four creasing rollers, folds the paper at 105-125 double folds per minute. The clamps are supported from below on rollers and, while in motion, are freely suspended between tension springs. The folding blade is 0.50± 0.0125 mm (0.020±0.0005 in.) wide, the slot extending somewhat above and below the normal position of the test specimen. Details : The vertical edges of the slot are cylindrical with radius equal to half the thickness of the blade. The four creasing rollers, each 6mm (approximately ¼ in.) diameter and 18 mm (approximately ¾ in.) long, are arranged symmetrically about the mid position of the folding slot and are provided with antifriction or jeweled bearings. 6 digit mechanical Counter, to register the number of double folds and to stop the instrument when the specimen breaks with reset knob to make it zero. Digital Smoothness & Porosity Tester https://www.advancetechinstruments.co.in/digital-smoothness-porosity-tester.htm https://www.advancetechinstruments.co.in/digital-smoothness-porosity-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Electronic Smoothness & Porosity Tester (BendtsenType) For Determining The Smoothness And Porosity Of Paper And Board, Based On Mass Flow Meter Principle. Provided With Imported Sensor And Accessories.Description/ Specification of Smoothness and Porosity Tester (Bendtsen Type) : We are offering our customers a wide range of Smoothness and Porosity Tester (Bendtsen Type). The Roughness of paper or similar material is defined as the volume of air that is forced by a specified pressure difference escapes in unit time by passing between the surface of the specimen and flat metal ring resting on a specimen. The values indicate the surface smoothness of graded paper suitable for good print quality. A sample is placed on a perfect plane glass plate, measuring head on the test piece and a controlled and low air in built pressure pass through a flat metal ring and the specimen. The pressure difference read on the display. Smoothness / Roughness Contact Pressure roughness - 98 kPa by measuring head of weight 267±0.5 gram Applicable Standard : SCAN P 21, P 60, BS 4420, TAPPI UM 535, ISO 2494, 5636/3, APPITA/AS 1301.440 DIN 53120 Ply Bond Tester https://www.advancetechinstruments.co.in/ply-bond-tester.htm https://www.advancetechinstruments.co.in/ply-bond-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Internal Ply Bond Tester is used to measure the internal bond strength of papers. Designed originally to evaluate the de-lamination strength of barrier materials comprised of kraft paper and sisal yarns, the Internal Ply Bond Tester has found many other uses in quality control laboratories in paper industry. The unit is used to measure the average force, in thousandths of ft. lb., required to de-laminate the fibers in the paper specimen, as described by the TAPPI “Useful Methods  403”. Other test includes de-lamination of bonding strength of coated papers stocks, the fibre bonding strength of kraft stocks (“Z” axis tensile) and the ply de-lamination strength of paper board. The Internal Bond Tester mat also be used as a coating pick tester. The procedures for this test are given in the TAPPI “Useful Methods 534”.General Features : A table-mounted unit designed for ease of operation, this model does not require an electrical power source. The unit consists of a base, a sample preparation device and a dual capacity free-swinging pendulum incorporating a ball nose-striking hammer. The pendulum pivots on ball bearings and a striking hammer gives point contact on the aluminum angle of the specimen assembly. The energy of the pendulum may be changed by simple adding or removing weights. The dial has two scales, for light and heavy loads. The specimen is held between the base and the anvil of the test fixture by double-sided pressure sensitive tape. Test fixture provide a standard specimen of one inch square, with lamination assembled under calibrated pressure to assure uniform adhesion throughout the samples. Technical Specifications : Load Measuring System: Consist of a free swinging dual capacity, pendulum of 0 to 0.250 and 0.100 and 0.500 ft. lbs. Capacity, a frication pointer of transparent plastic and a calibrated dial to indicate the force expanded by the impact. The pendulum assembly is supported by a cantilevered column, pedestal mounted on a cast iron base. A dispenser for a double-sided pressure sensitive tape width 1” is also an integral part of this model and is mounted into the base of the instrument along with the sample preparation apparatus consisting of five positions, each having one base and one angle. The aluminum angles are retained in a fixture for ease of alignment and assembly. After the samples are prepared pressure is applied through a cam and a lever. The range of pressure is adjusted from 50 PSI to 200 PSI by changing the capacity washers furnished with the tester. Hand Held Moisture Meter https://www.advancetechinstruments.co.in/hand-held-moisture-meter.htm https://www.advancetechinstruments.co.in/hand-held-moisture-meter.htm Thu, 12 Sep 2019 00:00:00 +0530 The offered lot is prepared using the best in class raw material that is sourced from the reliable places only. Besides, we check it for quality prior to procurement. With our modern transportation amenities, safe and on-time deliveries are rendered by us!   Details : Designed to check the moisture levels in paper products such as kraft stock, baled scrap paper, and other materials. Resistance technology recognized around the world as the most accurate method for measuring moisture. Averages up to 100 accumulated readings. 4.3 % - 18% moisture range on paper.0-100 reference scale for relative moisture indications in various hygrosopic materials. 5% - 40% moisture range on baled scrap paper Digital readout Includes (1) 9 volt battery Proven microcontroller circuit One year Warranty Digital Brightness Tester https://www.advancetechinstruments.co.in/digital-brightness-tester.htm https://www.advancetechinstruments.co.in/digital-brightness-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 This instrument can be used to measure colour parameters of the surface of an object. It can also be used to determine the colour difference between two coloured samples using various international standard methods for objective comparisons, which will give quantitative colour difference perceptibility or acceptability in colour matching. The degree of whiteness of white objects may be determined in accordance with various whiteness standards, as can light scattering coefficient, absorption coefficient, degree of opacity and degree of yellowness, yellowing tendency of paper etc. Instead of using visual assessment this instrument can assess the degree of colour changing and staining in textile colour fastness.Accessories : Powder disc Standard white powder (Barium sulphate) plastic white plate (negligible fluorescent) plastic white plate (fluorescent) Black cylinder Power cable Pulsed xenon lamp Fuse (NM51 1A/250V) Paper Digital Oven https://www.advancetechinstruments.co.in/digital-oven.htm https://www.advancetechinstruments.co.in/digital-oven.htm Thu, 12 Sep 2019 00:00:00 +0530 The moisture content of the paper is defined as the loss of weight of sample, dried under specified conditions to constant weight at a temperature of 1050C ï ± 20C and is expressed as a percentage of the weight of the moist sample.Scope : This method applies to papers and do not contain appreciable quantities of material, other than water, that will escaper from the paper at the temperature specified for the test. After drying enclose the sample quickly in the container and allow to cool for 45 min (Note 3). Equalize the air pressure outside and inside the container by momentarily opening and closing it. Weigh the container and its contents. Empty the container and reweigh it immediately, together with its lid. Bendtsen Smoothness Tester https://www.advancetechinstruments.co.in/bendtsen-smoothness-tester.htm https://www.advancetechinstruments.co.in/bendtsen-smoothness-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Roughness of paper is defined as the volume of air that, forced a specified pressure difference escapes in unit time by passing between the surface of the paper and a flat metal ring resting on the paper and exerting a definite pressure on int.Scope : This method applies to all kinds of paper and paper-board and describes the testing of conditioned specimens A measuring head with an air inlet tube on one side: on the bottom is a flat ring made of acid-proof steel: it has a mean thickness of 0.150 mm ± 0.002 mm and an inner diameter of 31.5 mm ± 0.2 mm. The range of the thickness readings should not exceed 0.004 mm. The mass of the measuring head should be 267.0 g ± 0.5 g . An air flow meter, consisting of three rotameter tubes : First tube - 10 to 150 ml/min Second tube - 50 to 500 ml/min. Third tube 300 to 3000ml/min The rotameter tubes should allow these air flows to be determined with an error of less than 2 ml/min and 5 ml/min, respectively. Laboratory Rotary Digester https://www.advancetechinstruments.co.in/laboratory-rotary-digester.htm https://www.advancetechinstruments.co.in/laboratory-rotary-digester.htm Thu, 12 Sep 2019 00:00:00 +0530 The Digester is a complete pulping unit for producing pulps by cooking wood chips in a manner similar to a commercial digester. The unit is easy to operate and features precise control of pulping variables to ensure good repeatability of results. Digital temp Indicator-cum-controller precisely control the temperature range upto-200 oC. The rotation with change in turning direction provide efficient agitation to the samples. Digital Core Crusher https://www.advancetechinstruments.co.in/digital-core-crusher.htm https://www.advancetechinstruments.co.in/digital-core-crusher.htm Thu, 12 Sep 2019 00:00:00 +0530 Compressive Strengthisthe maximum force developed a test specimen before rupture on the compression test carried to rupture under prescribed conditions. Compressive Strength (as used here) is the force per unit dia of test specimen. Short Span Compression Tester https://www.advancetechinstruments.co.in/short-span-compression-tester.htm https://www.advancetechinstruments.co.in/short-span-compression-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The Short Span tester is an advanced instrument which yields the national and international standard such as ISO, Tappi, and SCAN etc. The short span compression tester also reduces the factor which gives variation; Tester also reduces loading and unfavorable stress. It also avoids these factors giving result which have a material property unaffected by density and gram mage. The accuracy and repeatability of test result depends on the correct sample conditioning. The internal programming provided the rapid means of setting up the instruments. The facilities such as Peak hold at max load auto return after the completion of that test.Principle : A test specimen, 15 mm wide is clamped in pneumatically operated two clamps, 0.7 mm (0.0276 in.) apart. The clamps are forced towards each other until a compressive failure occurs. The maximum force causing failure is measured. Digital Thickness Micrometer https://www.advancetechinstruments.co.in/digital-thickness-micrometer.htm https://www.advancetechinstruments.co.in/digital-thickness-micrometer.htm Thu, 12 Sep 2019 00:00:00 +0530 The instrument has a castled stand and having two parallel, plane circular faces between which the test piece is placed for measurement. One of the faces (the anvil).In the measuring spindle there is a stationary lower measuring area of 200 mm2. The movable measuring area is fixed on a bar, which also supports the dead weight load. The pressure between the two faces is 100 kPa + 10 kPa. The measuring indicator is located on the top of the bar is connected with optical transducer.Details : The bar is lifted and lowered by electrical motor. When you push the button on the side of the instrument, the bar with the movable measuring area is lifted with a specified speed. The speed at which the pressure foot is lowered is controlled automatically and adjusted to 4.0 mm/s + 0.2 mm/s. Make a few lifting of the upper measuring area and check the zero position. Adjust the zero. Now the instrument is ready for use. A set of thickness filler guagues, with two value for 0.150 and another 802 ± 2 micron to be used for calibration. Concora Medium Fluter https://www.advancetechinstruments.co.in/concora-medium-fluter.htm https://www.advancetechinstruments.co.in/concora-medium-fluter.htm Thu, 12 Sep 2019 00:00:00 +0530 The prepared sample (for standard: 152.4 mm strips) is put in the upper opening. The strip is heated up to 177C between corrugated rotating discs, whereby the flute is formed and ejected at the lower opening.Using the included sample holder the self adhesive tape is applied to complete the sample preparation. Conventional equipment to flute samples of paper by rotating fluting rolls. Standard type “A” is supplied. Standard accessories : included are the rack and comb. The rack, with a profile corresponding to the fluting rolls teeth, has 9 crest and 10 valleys. The distance between the teeth are 8,50 ± 0,05 mm. and the highness of the teeth are 4,75 ± 0,05 mm. The comb has 10 projections of 19 mm long approx. and 3 ± 0,1 mm. height. RCT Sample Cutter https://www.advancetechinstruments.co.in/rct-sample-cutter.htm https://www.advancetechinstruments.co.in/rct-sample-cutter.htm Thu, 12 Sep 2019 00:00:00 +0530 Our reliable and superfast shipping facilities will not let you wait much and will efficiently deliver the range to your doorstep. We understand how important packaging is. Therefore, we make sure our products ate packed properly, have smudge-proof labels and are aesthetic to look to lure in more customers. The advance tech Sample cutter for ring crush tester (punch & die type )with high steel high chromium as per Tappi std. size 0.5 inch x 6 inch. Paper Punch & Die Cutter https://www.advancetechinstruments.co.in/paper-punch-die-cutter.htm https://www.advancetechinstruments.co.in/paper-punch-die-cutter.htm Thu, 12 Sep 2019 00:00:00 +0530 The paper circular punch & die cutter has a sheet metal base And incorporates a guide for the material to cut both top and bottom cutting blades are made from special knife steel high carbon high chromium and can be re sharpened. It eliminate testing error due to sample prepration, cutting sample size 100 cm2. Martindale Abrasion Tester https://www.advancetechinstruments.co.in/martindale-abrasion-tester.htm https://www.advancetechinstruments.co.in/martindale-abrasion-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Abrading instrument, consisting of a horizontal turntable with a center clamp, which revolves at 70 to 75 rpm, upon which the specimen is attached, and two weighte parallel arms, each carrying a special abrasive embedded rubber whell, freely rotating on a ball-bearing horizontal spindle, and each resting on the specimen with a known dead weight load and an adjustable vacuum system for debris removal. For the dry paperboard test, 1000 gf or 500 gf is used with non resilient wheel. For the dry paper test, 500 gf or 250 gf is used with resilient wheels. For the wet test, 500 gf is used the same wheels as used in the dry tests. In all cases, the type and grit of wheels shall be agreed upon by user and supplier. The surface of the table is covered with a disk of soft rubberized material 0.762 mm (0.03 in.) thick each abrasive wheel is 44 to 51 mm (1 ¾ to 2 in). in diameter and 12.7 mm (1/2 in) thick and composed of a special finely screened and standardized abrasive. A revolution counter is attached to the table. The lines of contact of the wheels on the specimen are at right angles to the parallel supporting arms and situated 25 mm (1 in) from the center of the turntable towards the axis about which the supporting arms turn. The center of the line of contact of the wheel on the arm from which the turntable revolves is 31 mm (1 7/22 in) to the left. In this manner, where in contact with the turning specimen, the two wheels revolve in opposite directions and exert a combined abrasive, compressive, and twisting action over a circular path approximately 3000 mm2 (4.6 in2) in area, twice during each revolution of the specimen. 4.1.1 for the wet abrasion test, a rubber-covered turntable with an annular raised rim is used, to permit the surface of the specimen to be covered with water during the test.4.2 Brush, soft brush about 12-13 mm (1/2 in) wide the bristles about 25 mm (1 in) long. Filter paper, sintered glass or Gooch cruicible, for wet abrasion residue. Resurfacing turntable, a rubber covered turnatable on which an abrasive disk is mounted, for resurfacing the wheels. Air Knife Coater https://www.advancetechinstruments.co.in/air-knife-coater.htm https://www.advancetechinstruments.co.in/air-knife-coater.htm Thu, 12 Sep 2019 00:00:00 +0530 The term coated applied to any paper or board to which has been applied a coating of any character or substance. In the present case of coating the printing grades of paper and boards, the primary objects in the coating operation is to produce a sheet with an even, semi-absorbent surface for printing. This is effect­ed by covering the fibers on the surface of the paper and filling the hollows between them with finely divided mineral matter, mixed with an adhesive or "size". When such paper is calendered, there results a smooth even surface, which reproduces the half tone dots of the printing plate much more faithfully than any plain paper.    Air Knife Coater : The lab coater is designed to make it possible to obtain small coated paper samples. Different types of coating mixtures can be used to obtain the coated paper samples. The coating result corresponds well to that obtained by production airknife coaters.The coater consists of a welded squire shaped frame of the size length 24", width 14" and height 12". The frame contains a trans­former , a blower with a manometer 8-800 mm water pressure and a reversible motor.On the front are the controls. When the main switch is in posi­tion 1, the table can be moved. In position 2, the blower for the air knife will operate. Beside the main switch is the switch for the reversible motor that moves the table with the sample for­ward and backwards. A movement to the right moves the table to the right and the monometer is then visible. By switching on to the left the table goes back. On the right of the main switch is the regulating transformer for the blower. The air pressure is read, on the monometer. Across the table over the whole width is the air knife.It is possible to adjust the opening of the slit by the screws along the length of the airknife and is generally kept at 0.04-0.05 cm.Test the coated sheets and uncoated base paper sheets for the following and compare the results and report : Gloss Basis Weight Oil Absorption Test Surface Smoothness. Ash Tester https://www.advancetechinstruments.co.in/ash-tester.htm https://www.advancetechinstruments.co.in/ash-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The ash content of paper is defined as the weight of the residue after complete combustion of a sample at a temperature of 9250 C ± 250 C under specified conditions and is expressed as a percentage of the weight of the oven dry paper.Scope :The ash content of paper gives an estimate of the content of mineral salts, loading materials and other inorganic matter, but is not quantitatively equal to this content because the weight of some of these substances is altered during ignition. Box Compression Tester https://www.advancetechinstruments.co.in/box-compression-tester.htm https://www.advancetechinstruments.co.in/box-compression-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Box Compression Strength, the maximum force developed a test specimen before rupture on the Box Compression Strength carried to rupture under prescribed conditions. Electronic Box compression Strength Tester meets the requirements laid down in the testing standards as per TAPPI standards.Details : In the foremost parts are the platens, a upper and a lower one, for insertion of test specimen. Movable by a load sensor from DC Motor & Reduction Gear, The Moveable platen is directly attached to a force signal transmitter. The bottom platen is fixed. The Moveable platen  crush  the specimen. The initial distance between the middle of the stationary platen and the middle of the movable platen is 100 mm. It is possible to alternatively work with different distance between the platens. The compressive length may be selected by loosening the top screw of the upper platen, loosen it and Tight and place it in its higher or lower position, as you require. Tester Specification : Mains Supply - 220 Volts ±10%, 50 cycles (if not otherwise specified in your order and acknowledge by us) Load Sensor - 2000 kg or depend on requirment Measuring Range -  2000 kg Accuracy - Better than ± 1% of force reading, but not better than ± 1 . Display - 4 1/2 digit display Power Requirement - Capacity 1000 Watt Deformation Speed - Selected/Variable Automatic return of platens after rapture Electronic overload protection at load cell capacity. Cobb Sizing Tester https://www.advancetechinstruments.co.in/cobb-sizing-tester.htm https://www.advancetechinstruments.co.in/cobb-sizing-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Basically Cobb Tester consists of a support frame  and a metallic cylinder about 5 cm high  with an internal cross section  of 100.00 cm2 (11.29 cm internal diameter).Clamping System :The cylinder is clamped by spring loaded upper plate lined with rubber mat automatically get clamped  as soon  as you release the handle. The base board is covered with a rubber mat. The test piece on top by the mat so that a leak proof scale is formed when cylinder is clamped.The  lower edge of  the cylinder   is machine smoothed. The inner surface  of the cylinder is provided with a shallow groove which is parallel to the cylinder axis  and bends  over the  rim  of the cylinder.  The groove helps in  draining off the water after test. A further development of the well  known Cobb Sizing Tester. The liquid container, filled the specified  amount of liquid, can be turned up-side down by means of a knob and after the necessary time has elapsed, turned back again, can be used several times before liquid  has to be renewed. The lid is provided  with spring loaded finger.A stainless steel roll of 20 cm face and weighing 10.0 + 0.5 kg as been provided to apply for blotting the water. Digital PH Meter https://www.advancetechinstruments.co.in/digital-ph-meter.htm https://www.advancetechinstruments.co.in/digital-ph-meter.htm Thu, 12 Sep 2019 00:00:00 +0530 This instruments is a high performance Digital PH meter intended for use in applications ranging from laboratory. It truly repre­sents a level of excellence for electro-chemical analysis, it offer the accuracy of digital measurements with its freedom from ambiguity rendering it an ideal apparatus for use by semi-skilled person.The stability, quick response, high input resistance make the instruments for uses requiring precision. The instruments to claim for its high stability, reliability and durability with very low consumption.Technical Specifications : pH, mV and  temperature measurement. Automatic and manual temperature compensation. Three point pH calibration, automatic buffer recognition . Electrode slope and mV offset display. Microcontroller  based Measuring range - 0 to 14 pH pH resolution - 0.01 pH pH accuracy  - ± 0.02 pH MV range  - ± 1999 mV Temp. - 0 - 100 deg.c Electrode  -  pH combination electrode with built in temp. sensor. Accessories - Buffer tablet Digital Stiffness Tester https://www.advancetechinstruments.co.in/digital-stiffness-tester.htm https://www.advancetechinstruments.co.in/digital-stiffness-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Digital Stiffness Tester Are manufactured With High-quality Material. The tester are equipped with for results reading according to TAPPI T 556 and SCAN-P 29 in mN to mNm/ The calculation of this specific bending stiffness and its calibration by using the stiffness tester is based on the standard DIN 53 121 “Determination of the bending stiffness according to the beam method” section 3.1.3.1, formula (4).The assumptions for measuring condition were formed according to following measuring condition. Bending angle 50 Width of specimen 38,1 mm Bending length 50 mm The stiffness tester measures the resistance to bending of the test material by recording the maximum bending force which arises when the test material during content turning speed is turned to set bending angle with set bending lengths.Bending Resistance: Stiffness of paper is defined as the resistance to bending offered by a rectangular test piece with its longer side parallel to the direction (machine or cross) for which the stiffness is measured. The stiffness is considered to be measured towards the side (top or wire) that is concave during bending The bending stiffness Tester meets the requirements laid down in the testing standards as per TAPPI standards Accuracy Better than ± 1% of force reading, but not better than ± 1 Digital Tearing Resistance Tester https://www.advancetechinstruments.co.in/digital-tearing-resistance-tester.htm https://www.advancetechinstruments.co.in/digital-tearing-resistance-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Tear strength tester (elemendroff type) with (selected  pendulam) to measure the tear strength value of the sample.Technical Specifications : Interchangeable pendulum for different range : 0-2000 mN.(Extra Light,A4) 0-8000 mN.(Light, A) 0-16000 mN.(Medium, B) 0-32000 mN.(Heavy, C) 0-64000 mN.(Extra Heavy, D) Tearing sample cutter. Set of calibration weights. Specimen : Specimen Height - 62 mm ± 0.2 mm.       Specimen lengt - 50 ± 2.0 mm Option : Manual Tearing Sample cutter For preparation of tearing test specimen.Applications : Paper Packaging industries Elmendorf Tearing Resistance Tester https://www.advancetechinstruments.co.in/elmendorf-tearing-resistance-tester.htm https://www.advancetechinstruments.co.in/elmendorf-tearing-resistance-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Tear strength tester (elemendroff type) with (selected  pendulam) to measure the tear strength value of the sample.Technical Specifications : Interchangeable pendulum for different range : 0-2000 mN.(Extra Light,A4) 0-8000 mN.(Light, A) 0-16000 mN.(Medium, B) 0-32000 mN.(Heavy, C) 0-64000 mN.(Extra Heavy, D) Tearing sample cutter. Set of calibration weights. Specimen : Specimen Height - 62 mm ± 0.2 mm.       Specimen lengt - 50 ± 2.0 mm Option : Manual Tearing Sample cutter For preparation of tearing test specimen.Applications : Paper Packaging industries Environmental Chamber https://www.advancetechinstruments.co.in/environmental-chamber.htm https://www.advancetechinstruments.co.in/environmental-chamber.htm Thu, 12 Sep 2019 00:00:00 +0530 Conditioned : In moisture equilibrium with a conditioning atmosphere, A sample of a paper or board is conditioned and said to be in equilibrium with the conditioning atmosphere when it has been exposed to the atmosphere long enough for the results of two weighings of a test piece, per formed at an interval of at least 1 h, not to differ by more than 0.25 per cent.Conditioning atmosphere :For general purposes the conditioning atmosphere in testing paper and board shall be : Temperature - 230 ± 10 C Relative humidity - 50 % ± 2% Flotation Cell https://www.advancetechinstruments.co.in/flotation-cell.htm https://www.advancetechinstruments.co.in/flotation-cell.htm Thu, 12 Sep 2019 00:00:00 +0530 Floatation is a physical-chemicals process of separating materials. It is based on the phenomenon that separation is achieved by influencing the wet ability with water of the particles to be separated, whether the surface of these particles is hydrophilic or hydrophobic. The water repellency of the surface of the particles to be separated is achieved by the addition of special hetero polar chemicals, called collectors, which deposit on the surface of the particles. In the case of ore and mineral floatation, the polar metal- affined component of the collector deposits on the surface of the particle of the collector deposits on the surface of the particle so that the a polar component, mostly a CnN2n-1 chain, a with a dense packing of the adsorptive substance steeply erects on the surface of the particle, thus rendering it difficult to wet. At the same time, the treated particles can deposit on air bubbles that are introduced into the suspension, stabilized by frothers acting on the gas liquid boundary, as a result of the buoyancy of the air bubbles, the adhering particles are conveyed to the surface of the slurry or suspension to concentrate as froth, in which from they can be removed all hydrophilic particles remain in the slurry or suspension.Technical Specifications : Mains Supply - 220 volt ±10%,50 cycles (if not otherwise specified in your order and acknowledge by us) Rpm meter - Digital display to read out  revolution Accuracy - Better than ± 1% of force reading, but not better than ± 1 . Motor Rating - 180 Vdc ,1 hp . Speed - Variable Power Requirement - Capacity 1000 Watt Gurley Type Smoothness & Porosity Tester https://www.advancetechinstruments.co.in/gurley-type-smoothness-porosity-tester.htm https://www.advancetechinstruments.co.in/gurley-type-smoothness-porosity-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The instrument consists of an outer cylinder, which is partly filled with oil, and an inner cylinder which slides freely in the outer cylinder. The specimen is clamped in position such that the air entrapped in the inner cylinder is found to pass though it to escape. The inner cylinder is graduated so that the time required to pass a given amount of air through the specimen can be recorded.Smoothness test :The rate of lateral air flow between several sheets of paper depends upon the smothness or roughness of their surface. By taking the time for 50 cc. of air to escape as measured on the inner cylinder, the smoothness is measured. The test can be adapted for paper boards and other material.Porosity test :One square inch of paper is exposed to the air pressure exerted by the inner cylinder floating in oil. The rate of air flow through the paper is its porosity. Air escapes through holes in the bottom clamping plats elastic gaskets on the adapter plate prevent leakage over the surface.Softness tester :Four softness plugs, forced into the paper sample by the weight and lever arm, constrict the space for air escape, depending upon how deeply the plugs compress the paper. The resulting rate of air flow is a measure of the paper’s softness, or compressibility. Horizontal Tensile Tester https://www.advancetechinstruments.co.in/horizontal-tensile-tester.htm https://www.advancetechinstruments.co.in/horizontal-tensile-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 Tensile strength, the maximum tensile force developed in a test specimen before rupture on a tensile test carried to rupture under prescribed conditions. Tensile strength (as used here) is the force per unit  width of test speciman. Stretch, the maximum tensile strain developed in the test specimen before rupture in a tensile test carried to rupture under prescribed conditions. The stretch (or percentage elongation) is expressed as a percentage, i.e., one hundred times the ratio of the increase in length of the test specimen to the original test span.Tensile energy absorption (TEA) the work done when a specimen is stressed to rupture in tension under prescribed conditions as measured by the integral of the tensile strength over the range of tensile strain from zero to maximum strain. The TEA is expressed as energy per unit area (test span x width) of test specimen.Tensile stiffness, the ratio of tensile force per unit width to tensile strain with in the elastic region of the tensile strain relationship. The elastic region of the tensile strain relationship is the linear portion of the load elongation relationship up to the elastic limit. The elastic limit is the maximum tensile force above, which the load elongation relationship departs from linearity. (Tensile stiffness is numerically equivalent To E  Where E is the modulus of elasticity and is sample thickness).Breaking length, the calculated limiting length of a strip of uniform width, beyond which, if such a strip were suspended by one end, it would break of its own weight.Horizontal Tensile Strength Tester meets the requirements laid down in the testing standards as per TAPPI standardsTechnical Specifications : Mains Supply - 220 Volts ±10%, 50 cycles (if not otherwise specified in your order and acknowledge by us) Load Sensor - 50.0 kg. or depend on requirment Measuring Range - 499.9N Accuracy     - Better than ± 1% of force reading, but not better than ± 1 . Display - lcd display Clamps - Tightening clamps for 15 mm wide strips by pneumatic Strip Dimension - 15 x 180 mm Clamping length - 100 150,180 mm Instrument Air - 300 kPa Computer Output - com port to transfer the data on pc Power Requirement - Capacity 300 Watt Deformation Speed - Selected/Variable Automatic return of platens after rapture Electronic overload protection at load cell capacity. Lab Hydrapulper https://www.advancetechinstruments.co.in/lab-hydrapulper.htm https://www.advancetechinstruments.co.in/lab-hydrapulper.htm Thu, 12 Sep 2019 00:00:00 +0530 Lab Hydrapulper is a complete pulping unit used for marking pulp from secondary fiber waste paper, on lab scale. It can also be used for mechno-chemical pulping. It has 30 liters capacity and can be also made available in 10 & 20 liters capacity, if required. The tub made of stainless steel, is provided with lid to fit tightly on the tub. There is an outer cover on the tub to make an access to the heaters and their connections. Four Heaters of 500 W each are fitted in the double wall annular space of the tub with glass wool as heat insulation to provide the heating controlled through thermostat. The Helicon Turbine fitted inside the tub is driven through V-Belt by the 5 HP motor at 500 RPM, for the desired time duration to form the pulp, at around 80 0C. The pulp samples can be checked by opening the top lid at intervals to ascertain its readiness.Features : Tub made of stainless steel, fitted with top opening, lid and bottom drain valve. Available in 10, 20 & 30 Liters capacity. Helicon-Turbine fitted inside the tub which is driven by 5 HP motor at 500 RPM with 440 V 3-Phase, 50 Hz supply. Special tool made available for fixing and withdrawing of turbine. Heaters are provided in the double walled space, heat insulated with glass wool. Temperature is adjustable upto 100 0C and maintained at any value through thermostat control. Drain valve provided at bottom for emptying the tank. Complete unit with motor and control panel mounted on firm base frame. Technical Specifications : Mains Supply - 415 Volts ±10%, 50 cycles (if not otherwise specified in your order and acknowledge by us) Tub Material - Stainless Steel Tub Capacity - 30 liters (other capacity of 10 & 20 also available) Motor - 5 HP, 920 RPM Heaters - 500 W each Thermostat control  - Upto 1000C Lab Valley Beater https://www.advancetechinstruments.co.in/lab-valley-beater.htm https://www.advancetechinstruments.co.in/lab-valley-beater.htm Thu, 12 Sep 2019 00:00:00 +0530 Beater of valley type is used for laboratory beating of pulp under standardized condition. The degree of betting can be varied. Beating is a preliminary step to the testing of the physical properties of pulp. In principle, this standard applies to all kinds of satisfactory results with certain extremely long fibred pulps, such as cotton lintersApparatus :The lab beater consists of a pulp chest of acid proof ground and polished internally. The pulp chest is divided in the centre and forms a circular basin in which the pulp can flow around. A hardened, portion separate the two halves of the pulp chest. The pulp between the beater roll and the beater plate. The beating pressure is controlled by means of the lever which is loaded with dead weights.A measured quantity of pulp with a specific consistency is beaten between the knives in the beater. Samples of the beaten pulp are taken at predetermined intervals during the beating. Patra Type Fluff Tester https://www.advancetechinstruments.co.in/patra-type-fluff-tester.htm https://www.advancetechinstruments.co.in/patra-type-fluff-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 A sample is placed between the blanket and steel roll and sample is moved between the roles under nip pressure. After selected number of sheets have been passed the fluff is transferred to blanket cylinders and a linen counter moved at the top of the machine to count the numbers of particles & fibers adhering to a given area of blanket.Technical Specifications : Nip pressure - 13.5 Kg. by dead weight roller. Blanket cylinder - 10” wide x 6” dia. Blanket material - Can be easily changed Measuring area - One square inch. Sheet feeding system    - Manual and sheets are pressed into the nip between rubber  blanket and printing plates cylinder Pulp Disintegrator https://www.advancetechinstruments.co.in/pulp-disintegrator.htm https://www.advancetechinstruments.co.in/pulp-disintegrator.htm Thu, 12 Sep 2019 00:00:00 +0530 A pulp sample is said to be disintegrated when it has been subjected to mechanical treatment in water so that interlaced fibres, which were free in the pulp stock, are gain separated from one another without appreciably changing their structural properties.Apparatus : A disintegrator consisting of : A cylindrical container, provided with four vanes on the inside. A propeller mounted on a vertical shaft, driven by electric motor. A counter for recording the number of revolution and auto stop at set counter. Technical Specifications : Mains Supply - 415 Volts or 220volt ±10%, 50 cycles  (if not otherwise specified in your order and acknowledge by us) Revolution Range - 99999 rpm Accuracy - Better than ± 1%. Display - Seven segment  digital read out Rapid Sheet Dryer https://www.advancetechinstruments.co.in/rapid-sheet-dryer.htm https://www.advancetechinstruments.co.in/rapid-sheet-dryer.htm Thu, 12 Sep 2019 00:00:00 +0530 Rapid Dryer is used for quick drying of wet pulp or paper samples before measuring dry weight, while determining moisture content. A wet sample of pulp or paper is placed between the upper and the lower drying plates of the dryer. The temperature of the dryer is adjustable, allowing precise control of the drying conditions.After the prescribed drying time, the samples can be weighted to determine the moisture / solids content.Features : Rectangular Drying Plates Lower Plate is lined with wire cloth to lead off vapour during drying Adjustable thermostatically controlled drying temperature over a wide range Switch provided with indicator lamp. Upper and lower drying plates are heated with flat electrical elements. Technical Specifications : Sheet Size - Max width 250 mm, Max Length 300 mm Temperature Range - up to 1800C ± 100C Power Consumption - 0.8 KW Heater - Flat Electrical Elements single phase, 220 V, 400 W each for upper and lower plates. Schopper Type Tensile Tester https://www.advancetechinstruments.co.in/schopper-type-tensile-tester.htm https://www.advancetechinstruments.co.in/schopper-type-tensile-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 The machine in designed for determining the tensile  strength of  sheet  material such as paper, paper board,  plastics, metal foil, etc. The testing is made by inserting a sample between  two vertical  grips, and increasing the load until the sample  breaks. The elongation of the sample is measured simultaneously.Determination occurs by means of  a pendulum balance. When the inserted sample is subjected to a  strain,  the pendulum will make a deflection is indicated on a scale  directly in kilograms. Different load weights for the pendulum correspond to the respective graduation.The graduation 0-500 g only correspond to bare pendulum without extra load.The elongation is determined by measuring the increase in the distance between the clamps, which is indicated on the elongation scale. This scale has graduation in millimeters and in  per  cent based  on  180 mm testing length (which is a  standard  in  paper testing).  Should the elongation be wanted in per cent  based on other testing lengths, this must be calculated.Tensile Strength Tester (schopper type ) meets the requirements laid down in the testing standards as per  TAPPI standardsTechnical Specifications : Mains Supply - 220 Volts ±10%, 50 cycles (if not otherwise specified in your order and acknowledge by us) Measuring Range - Low range – 0 to 300.0 N,  high range – 0 to 600 N Accuracy    - Better than ± 1% of force reading, but not better than ± 1 . Clamps - Tightening clamps for 15 mm wide strips Strip Dimension - 15 x 180 mm Clamping length - 0-250 mm adjustable Power Requirement - Capacity 250 Watt Fuse -  5 Amp. Glass tube fuse Deformation Speed -  Selected/Variable Automatic return of platens after rapture Surface Wax Stick https://www.advancetechinstruments.co.in/surface-wax-stick.htm https://www.advancetechinstruments.co.in/surface-wax-stick.htm Thu, 12 Sep 2019 00:00:00 +0530 Dennison standard paper testing waxes are designed for use by paper and coated paper manufacturers, printers, lithographers, and other concerned with the development, inspection and control of paper for coating and printing purposes.The use of these waxes I described by the Technical association of the pulp & paper industry in relation to the surface strength measurement of paper products. Method T456-SU-65 published by the Association gives their latest approved method for this measurement. The use of these waxes is also described by the American society for testing and Materials in their method D2482-66T.The wax test is applicable to coated and uncoated papers and is formulated to evaluate the surface strength of paper or its resistance to picking. This test may be conducted to determine the degree of sizing in the coating in relation to the required press conditions, to estimate the ease with which a coating may be removed or “picked’ from the bodystock, and the tendency of the bodystock to split or the printing process. It is used in a similar manner for evaluating uncoated papers and other surfaces.The series of waxes have graded adhesive powers. They run from 2A, which has the least adhesive strength, and increase by small graduated amounts to 23A which has the greatest adhesive strength. Hence there is an increase in the degree of adhesion to surface fibres or coating coincidental with the increase in wax numbers.The complete series consists of 18 waxes, Nos. 2A, 3A, 4A, 5A, 6A, 7A, 8A, 9A, 10A, 11A, 12A, 13A, 14A, 16A, 18A, 20A, 23A,  and is available as a set in a cabinet, with an alcohol lamp, instructions, and accessories. Wood Chip Classifier https://www.advancetechinstruments.co.in/wood-chip-classifier-supplier.htm https://www.advancetechinstruments.co.in/wood-chip-classifier-supplier.htm Thu, 12 Sep 2019 00:00:00 +0530 Chip Classifier is used for rapid and reproducible analysis of chip with respect to size and thickness. The unit is easy to operate and helps in segregating the chips in various classified sizes for analysis and corrective  action. Four standard size screening aluminum tray plus one for dust calculation are included. The unit is attached to guide mounted on the sliding bars, which are moved by eccentric arn in the separation of the chips into various fractions. Taber Stiffness Tester https://www.advancetechinstruments.co.in/taber-stiffness-tester.htm https://www.advancetechinstruments.co.in/taber-stiffness-tester.htm Thu, 12 Sep 2019 00:00:00 +0530 We Supply Taber Stiffness Tester All Across india. These Machines Are manufactured With High-quality Material. Advancetech Stiffness tester (taber type) is used to evaluate stiffness and resiliency properties of materials up to 10,000 Taber Stiffness Units. This precision instrument provides accurate test measurement to ±1.0% for specimens 0.004" to 0.219" thickness. Materials include paper products, cardboard, plastics, metals, textiles, rubber, wire, tubing, felts and other sheet materials.Incorporated in the Stiffness Tester is a bi-directional pendulum weighing system. Providing an accurate and responsive method for measuring small load increments, this system is a critical component for determining material stiffness or resiliency. Canadian Freeness Tester https://www.advancetechinstruments.co.in/canadian-freeness-tester.htm https://www.advancetechinstruments.co.in/canadian-freeness-tester.htm Mon, 16 Sep 2019 00:00:00 +0530 We Are prominent Manufacturer, Dealer, Supplier & Exporter of Canadian Freeness Tester in Uttar pradesh, India. We Supply Canadian Freeness Tester All Across india. These Canadian Freeness Tester Are manufactured With High-quality Material. The Canadian Freeness (CF) number of pulp is a measure of the drainability of a suspension of pulp in water, determined and expressed as specified in this method.A known volume of pulp in aqueous suspension is drained through the fibre mat, formed on a screen plate during the test, into a funnel provided a bottom and a side orifice. The filtrate collected from the side orifice is measured in a cylinder graduated in millimeters, as a Canadian Freeness number of pulp.Limitation of the Test : This method applies to any kind of pulp with this limitations. The Canadian Freeness test gives acceptable results only if a sufficiently dense mat of fibres is formed on the screen plat. For this reason the test is not recommended for very short-fibred pulps such as those from well beaten hardwood, as most of the fibres may pass through a the screen plate, and high CF number will result although the pulp will drain slowly on the paper machine.The most reliable results are obtained within the CF number range 30-850. Fibre Classifier https://www.advancetechinstruments.co.in/fibre-classifier.htm https://www.advancetechinstruments.co.in/fibre-classifier.htm Wed, 18 Sep 2019 00:00:00 +0530 We Are prominent Manufacturer, Dealer, Supplier & Exporter of Fiber Classifier in Uttar pradesh, India. We Supply Fiber Classifier All Across india. These Fiber Classifier Are manufactured With High-quality Material. An agitated pulp suspension is fractionated by means of a screening process employing vertical screens with increasing wire sieve cloth numbers. The screens are mounted in tanks arranged in cascade.The mass of the fibres retained by each screen and of those passing all the screens in determined and expressed as a percentage of the oven-dry mass of the original sample.Fiber classifier consisting of five units mounted in cascade. Each units comprises a S.S. tank having the One of the flat sides has a rectangular aperture sealed by a detachable frame, which is clamped against a gasket. The frame is fitted with a slit plate and a wire sieve cloth, 335 cm2 (165mm x 23mm) in area and the lower edge of the frame is 50mm above the bottom of the tank .The slit plate, which equalizes the flow through the wire sieve cloth, can be removed from the frame. It has three vertical slots measuring the middle slot is located centrally with respect to the screen. The guide plate in the tank is mounted inside the screen and parallel and symmetrical with it. It has three vertical slots measuring 2mm x 190mm and set 41mm apart; the middle slot is located centrally with respect to the screen. The guide plate in the tank is mounted 14mm inside the screen and parallel and symmetrical with tank. Hand Sheet Former https://www.advancetechinstruments.co.in/hand-sheet-former.htm https://www.advancetechinstruments.co.in/hand-sheet-former.htm Mon, 16 Sep 2019 00:00:00 +0530 For producing the pulp sheet rapidly for physical strength test.in comparison to std sheet former, the apparatus reduced the time factor  increase the output reproducibility, reduce the operater influence  and fatigue  with out detriment to the final product. Selection of all function are automatic /manual with the white water recirculation system, pneumatic sheet press and rapid dryer  mounted on base table complete with all accessories. Suitable for sheet formation 165 mm diameter. Wood Chipper Machine https://www.advancetechinstruments.co.in/wood-chipper-machine.htm https://www.advancetechinstruments.co.in/wood-chipper-machine.htm Mon, 16 Sep 2019 00:00:00 +0530 Consistency Determination Apparatus https://www.advancetechinstruments.co.in/consistency-determination-apparatus.htm https://www.advancetechinstruments.co.in/consistency-determination-apparatus.htm Mon, 16 Sep 2019 00:00:00 +0530 Consistency determination apparatus for quick determination of pulp/stock consistency. The measured stock is poured on to the grid plate of the equipment and drained under suction. The filtration is repeated until the filtrate becomes perfectly clear. After drying and weight of the sheet the consistency can be determined.Optional : Vacuum pump Rapid Sheet Drier for shortening the drying time, as an optional accessory Couch Plate. Paper Testing Instruments https://www.advancetechinstruments.co.in/paper-testing-instruments.htm https://www.advancetechinstruments.co.in/paper-testing-instruments.htm Thu, 12 Sep 2019 00:00:00 +0530 Testing Instruments https://www.advancetechinstruments.co.in/testing-instruments.htm https://www.advancetechinstruments.co.in/testing-instruments.htm Thu, 12 Sep 2019 00:00:00 +0530 Pulp Testing Instruments https://www.advancetechinstruments.co.in/pulp-testing-instruments.htm https://www.advancetechinstruments.co.in/pulp-testing-instruments.htm Testing Instruments Thu, 12 Sep 2019 00:00:00 +0530 Hollander Beater https://www.advancetechinstruments.co.in/hollander-beater.htm https://www.advancetechinstruments.co.in/hollander-beater.htm Mon, 16 Sep 2019 00:00:00 +0530 We Are prominent Manufacturer, Dealer, Supplier & Exporter of Hollander Beater in Uttar pradesh, India. We Supply Hollander Beater All Across india. These Hollander Beater Are manufactured With High-quality Material.These Hollander Beaters are high on performance and are durable in nature. Our Hollander Beater is highly efficient due to the incorporation of high grade raw material in the production process and is used for uniform treatment of pulp under standard condition. We test our Hollander Beaters under stringent industry parameters for any type of flaws and faults.